Safe-Home.com

Healthier Living | Child Safety | Eco Friendly Tips

Prevent Most Water Heater Leak Disasters with Floodstop Automatic Water System

by Barbara 21. March 2014 13:19

Question: How can a Floodstop water heater automatic water system save me from a flooded basement?

Q: "I don't understand the value of installing a Floodstop single appliance water shut off system on my water heater. Isn't the water heater going to leak out all 40 or 50 gallons of water anyway? Thanks. Tom."

Answer: We discussed this with our Floodstop distributor, did some on-line research and remembered our own failed water heaters over the years. As our distributor explained, water heater water loss is typically from a pin-hole leak caused by corrosion to the inside lining of the tank. With Floodstop, you can choose to daisy-chain several sensors together to extend under the tank (if raised) or on the side where the sewer drain lies. Once a FloodStop sensor detects a leak, the Floodstop valve is immediately closed. Typically this pin-hole does not get larger because the Floodstop valve closure creates a kind of vacuum within the tank so no more water escapes. This is like putting your finger over the top end of a straw with water in it. That is why it is not necessary to have a device that shuts off the gas or the electricity to the water heater.

You, the home or apartment dweller, will know you have an issue to deal with when you get home hours, days or weeks later. You'll either hear the alarm or you'll go to the sink and there is no water immediately. Once you break the vacuum, the pin hole leak will again begin to drip. By then, the owner will shut off the water and the vacuum will resume. Then you'll be shopping for a new water heater.

Among plumbers and owners of high rise condo complexes,, the Floodstop is considered to be the best choice to prevent water disasters. Unfortunately, sometimes almost brand new water heaters begin to drip. Ex. My late Mom's installed 6 years prior to her death, lasted one year before it began to leak. Luckily it was in a visible basement area and was caught before any significant damage occurred.

Floodstop Automatic Water Systems for Water Heaters Come in These Sizes:

  1. FloodStop Water Heater Auto Water Valve Shutoff .75IN NPT, V.4
  2. FloodStop 1 Inch Valve for Water Heater/Softener, FS1.00-NPT-V4
  3. FloodStop Auto Water Valve for Water Heater/Softener, FS1.25 NPT
  4. FloodStop .50 Inch Valve for Heater/Softener, FS 1/2-NPT-V4
  5. FloodStop Automatic Valve for Water Heater/Softener, 3/4 In.Compression

Extra moisture sensors are also available. And these new Floodstops use either 4 AA batteries and AC power or can operate only on the 4AA batteries.

All Floodstop Units Include:

  • Motorized full-port stainless steel ball valve in brass valve body lined with Teflon (3/4 inch compression fittings).
  • Valve meets low lead drinking water standards of all US states.
  • Control unit with battery backup (4 AA batteries, not included).
  • AC power adapter (or use 4 AA Batteries as primary power source).
  • Water leak sensor.
  • Output contact wires (2).
  • Automatic Water Valve Shut Off 

Technical Specifications:

  • UL Listed Class 2 Wall Adapter, 115AC/9VDC.
  • UPC listed, full port, motorized ball valve: CNC machined.
  • Motor operates at 6VDC.
  • Rated 0-180 PSI. Max 250 PSI. Solid brass.
  • Signal outputs: 2 normally closed.
  • Alarm: beeping with mute button.
  • One year limited manufacturer's warranty.
If you need quantities for a condominium or apartment complex, please contact us directly.

Thanks for your question.

Sincerely, Barbara

Extending Sensor And Valve Shut Off Wires on FloodStop Water Heater Device

by Barbara 27. March 2013 08:33

Question about the Water Heater FloodStop with 3/4" valve FS3/4NPT and extending the length of the sensor and valve shut-off wires.

Q: "I purchased a Water Heater FloodStop with 3/4" valve FS3/4NPT. How far can the controller be located away from the shut off valve? 25 feet? Can I splice the controller to shut off valve wire and add 20 feet? Can I splice the sensor wire and add 30 feet? Thanks for all your help, Jerry"

Answer: Yes, you can extend the length of both wires. The controller can be located at any distance, so 25 feet is no problem. You can do this by splicing in a similar gauge paired wire as you suggested, or you can purchase our Controller to Valve Extension Wire, which is about 8 feet long. If you ordered 4 of them and simply plugged them into each other, you would not have to go buy wire or do any splicing.

You can splice into the sensor wire and extend it by 30 feet no problem. Or you can add Floodstop Individual Water Appliance Additional Water Sensor XS-01 unitsthat each have a 3 foot long wire and interconnect to give you more water sensor coverage. We do not have a controller to sensor extension wire, as the customized length can be so varied that the manufacturer did not create one.

Thank you for your question. Your question was asked of and answered by Mary Joyce and our distributor. I found it and thought it was a great one to share with others. Extending the sensor and valve shut off wires of all the individual FloodStop automatic water sensor and automatic valve shut off devices can be done in a similar fashion.

Sincerely,

Barbara