Safe-Home.com

Healthier Living | Child Safety | Eco Friendly Tips

Automatic Water Valve Shuts Offs and Alarms When Washing Machine Leaks

by Barbara 9. June 2016 02:38

Question about the products Washing Machine FloodStop FS3/4H-90 and FloodStop FS-3/4-H Washing Machine,In-Line Auto Water Valves.

Q:"Please tell me how many inches it is from the valve connector to the inside 90 of the device. Please send diagram with measurements if possible. Our valves are located in the back of the box and I have concerns if the valves will protrude past the front cover, plus I want to install water arrestors. Thanks, Jim."

Answer: We checked with the manufacturer's rep as this was beyond our expertise. Bob's response: "I have no diagram available for him, but understand his question.

The distance from the inlet end of the valve where the spinning female threaded collar is to the inside edge of the 90 degree downward outlet end of the valve is 2 9/16 inches (slightly over 2.5 inches). The FloodStop 3/4-H90 was specifically designed for wall box type installations. Numerous wall boxes were evaluated to determine the valve design so it would fit all brands. I cannot remember when someone returned a FloodStop 3/4-H90 because the outlet end of the FS valves did not protrude past the front cover of the wall box. Typically installing water arrestors increases the extension of the FS valves out from the hot and cold water hose-bibs."

FYI: The FloodStop is a dual valved water damage control device that turns off water to a washer machine when the water sensor (placed usually under the machine) senses moisture. The newest model utilizes AC power with a battery backup and has twin ball valves that shut off the water.

For those who have a different system, we do have the straight line version.

Thanks for your question.

Sincerely,
Barbara

Converting From Oil Furnaces to Natural Gas In NE USA States Means Adding Gas Safety Devices, Too.

by Barbara 4. December 2014 09:04

Question about safety issues when converting from oil heat to gas heat.

Q: "A natural gas shale line from Marcellus Shale gas in Pennsylvania may extend into the Northeastern states in the next year, if approved (Quote from CBS 12/3/2014) We currently are using oil heat. Replacing the furnace with natural gas will save us a lot of money. How can we avoid the health risks associated with natural gas?"Thanks Tom.

Answer: Continue using carbon monoxide alarms and smoke detectors as you have been doing, remembering to test them monthly and change batteries once a year. I would also suggest you add a Scentry III Gas Shut Off system on your main line into the home as well as Safe-T-Alert Combustible Gas Alarm or a Safety Siren III natural gas alarm near your natural gas appliances such as ranges, fireplaces, etc.

With the Scentry III GFRAB, you can add additional remote sensors, a battery back-up and a connection to a home monitoring system if you have one or plan to get one.

Remember that natural gas is lighter than air and "puddles" at the ceiling above the appliance using it. If near an open stairway, the gas will go to the top of the stairway.

An annual furnace tune up with filter change is needed with gas furnaces as well as with oil. If you want the best disposable furnace filters, use the 4 inch or 1 inch Safe Home filters.

Thanks for your questions.

Sincerely,

Barbara

 

Toilet Guardian Keeps Toilet Bowl Water From Overflowing Onto Your Floors

by Barbara 6. November 2013 10:44

Question about best way to keep toilets from overflowing.

Q: "I operate a day care center. The older children toilet themselves; the younger ones have supervision. We have problems with children using too much toilet paper. Then the toilet bowls overflow and there is a mess. What device or devices can we install to prevent these bowl overflows? Thanks. Sara

Answer: The Toilet Guardian TB1000B should save your toilets from overflows. Peace of mind at under $100, no plumber required if you are handy. (The plumber's fee is about the same as the unit in most areas.)

The Toilet Guardian includes a bowl sensor and a controller for an internal valve. When the sensor detects an impending toilet overflow, the sensor signals the controller and the internal valve is closed. This is a great addition to public restrooms, day care centers like yours, private homes, etc..

Battery operated (One CR-2477F Coin Battery), this automatic water shut off valve for the toilet water valve installs easily. Just attach to your existing fill valve at the water connection under the tank. When a potential water problem is detected, you hear the alarm and the water is shut off.

This patented design uses superior Texas Instrument MSP430 technology, replaceable battery (five year life), ceramic disk valve and high impact and chemical resistant materials. Each unit undergoes over 15 function, design and manufacturing tests before shipping.

Toilet Guardian Features Include:

  • No plumber required: easily installed.
  • Twin ceramic disk valves
  • TI MSP430 microprocessor
  • Stainless steel solenoid tested to over 500,000 cycles
  • 3V lithium ion battery w/5 yr. life (replaceable), CR2477F battery
  • Small, light weight, highly impact resistant plastic
  • Size: approximately 3 inches tall by 2 inches wide
  • 0 to 125 psi operating pressure
  • LCD icon display identifies the problem
  • Piezo buzzer for audible alert
  • Two Year Manufacturer's Warranty Against Defects

While you are at it, you should consider installing a Floodstop for your hot water heaters or at the very least a Water Screamer water alarm with 130dB alarm. Water heaters often are in isolated areas. No one knows there is a problem until the water leaks cause damage.

Thanks for your question. Please contact us for more information.

Sincerely,

Barbara

Stop Under Sink Water Leaks With Floodstop Water Valve Unit for Hot and Cold Water Lines

by Barbara 22. July 2012 07:01

Question about the FloodStop for Sinks Lead Free Water Valve FS3/8CD.

Question: "Our neighbor recently had extensive water damage from a leak under a bathroom sink. The sink is in a rarely used bathroom. The first hint of the water leak was the damp spot on the ceiling in the room below. What product do you suggest for protecting our guest room sink which is rarely used? Thanks. Sam."

Answer:  For a single location, install the FloodStop for Sinks Lead Free Water Valve FS3/8CD. The "CD" stands for compression fitting, i.e. no soldering is required. The Floodcheck water valves connect to the angle stops and supply lines. FloodStop water valves are full port ball valves that meet the California and Vermont lead free water valve standards for drinking water.  Add additional sensors for more coverage under the sink. Do remember that you will need an unswitched electrical outlet for power: electricity is used only when the sensor detects water.

When a hot or cold water leak is detected, Floodstop shuts off the water below the sink and sounds an 87 db alarm.

Installation:

    Connect the water valve to cold and hot water lines under the sink.
    Mount the control unit.
    Place sensor(s) on floor.
    Plug power supply into an unswitched outlet. Note: electricity is used only when the sensor detects water.

NOTE: DO NOT PLACE SENSOR DIRECTLY ON METAL PAN OR DAMP FLOOR. If no water is present and alarm sounds, place paper towel or cloth under sensor to "insulate" against floor dampness or metal of pan. When the paper or cloth gets wet, the sensor activates the shut-off and sounds the alarm.

How FloodStop (FS 3/8-CD) Works:

    FloodStop valves connect to the angle stops and supply lines.
    Water leak sensor is placed at the base of the fixture (sink, laundry tubs, bathtub, etc.).
    Valve remains open until a water leak or water loss is detected.
    Water on the sensor signals the Floodstop controller which closes the valve and alarms.
    Valve remains closed until system is reset, and sensor is dry.

FloodStop (FS 3/8-CD) Components:

    Motorized Ball Valves (Two Valves, 3/8 inch Compression Fitting).
    Control unit with battery backup (4 C batteries, not included).
    AC power adaptor (or use 4 C Batteries as primary power source).
    Water leak sensor (1.25" X 7.5").
    Output contact wires (2).

Technical Specifications:

    UL Listed Class 2 Wall Adaptor, 115AC/9VDC.
    UPC listed, full port, motorized ball valves.
    Motor operates at 6VDC.
    Rated 0-180 PSI. Max 250 PSI. Solid brass.
    Signal outputs: 2 normally closed.
    Alarm: beeping with mute button.

Features:

    For added water detection protection, add more sensors. Sensors plug into sensors, NOT the Control Box.
    The 3/8 inch valve is 3.75 inches long.
    Controller has reset and test buttons to test valve performance plus battery back up.
    Easy to install, operate, and maintain.
    Designed for residential, condo and apartment dwellings.
    Full port ball valves automatically shut off water supply to sink when water sensor/sensors get wet.
    Power: 120VAC and/or battery backup (4 C batteries).
    No wires to route throughout the home.
    Alarm: beeping with mute button.
    Water Sensor: 1.5" X 7.5", double sided. Additional sensors may be added in series.
    AC Adapter Cord Length: 6 Ft.
    Wire Length from the Controller to the Valve: About 30 Inches Long.
    FloodStop Controller:
        3 buttons: Mute, Close Valve and Open Valve.
        Water sensitivity adjustment. Clockwise: less sensitive. Counter clockwise: More sensitive.
        4-pin connection to valve/sensor connector.
        Outputs: Normally closed. Contacts for any device that can utilize them, like auto phone dialers, alarm systems, X10 home automations devices.
    One year limited manufacturer warranty.

I hope this helps with your situation.

If you want whole house protection, a install the Floodstop Whole House Auto Water Valve System. This unit comes in 3/4”, 1” and 1.25” valve sizes. Included with each system are one Motorized Full-Port Ball Valve,one Controller (that shuts off the main water valve),four Sensor Modules, four sensors to place in areas you want protected, one transformer for the controller and four low voltage transformers for the sensor modules. This unit screws onto the water pipe, i.e. it is an NPT or National Pipe Thread Tapered Thread.

Go to WWW.SafeHomeProducts.com for more information.

Thank you again.

Sincerely,

Barbara

FloodStop Automatic Water Valve and Alarm for Dishwasher, Toilet or IceMaker

by Barbara 12. July 2010 22:59

Question about the Floodstop 3/8 Inch Automatic Water Shut-Off and Alarm.

Q: "Water is seeping through the floor under my dishwasher. Right now there is just a small wet spot. My basement is to be finished this winter so I want to protect the house from water leaks from the dishwasher, toilets, etc. if I can. I see that you have a device that would shut off the water to the dishwasher and sound an alarm if the new dishwasher (to be installed soon) leaks in the future. How complicated is it to install the valve? What other units are available? Thanks. Tom"

Answer: My suggestion is to have the appliance store deliver the new dishwasher and have their plumber install the Floodstop at the same time. Check your local tax laws. Currently, at least in Iowa and in Pennsylvania, you don't pay sales tax on the appliance if the store delivers the unit and does the installation. Depending upon your locale, the additional plumbing charge may be $50 and up. The protection is worth it.

Most dishwashers are next to a sink since they use the sink drain. The plumber would install one or more water sensors on the floor where the dishwasher will be placed (we recommend a minimum of two), the water valve, attach the alarm valve turn off unit to the wall (probably under your sink), and plug in the unit. The sensors should be tested by wetting them. After they are dried and the water valve is reset, then the dishwasher is installed.

The FloodStop unit for dishwashers and toilets has a 3/8 inch compression valve that connects to the angle stop and the supply line. You do need electricity unless you plan to change batteries at least once per year. (The unit draws power only to open or close the valve.) For AC, use the 4 C batteries, not included, as back-up. Contacts allow the option of connecting to phone dialers, alarm systems, X10 home automation devices, etc. There is also a 9 foot controller valve extension cord available to allow mounting of the controller in a more or less visible location. The length of cord included with Flood Stop leak detection alarms is 2.5 feet.Transformer extension wires are also available.

We also sell Floodstops for water heaters, washing machines that does not require a plumber, sinks, icemakers with 1/4 inch lines etc. All units have a one year warranty by the manufacturer. We've had customers literally saved from flooded homes from these units especially from leaking washers and water heaters.

Floodstop Dishwasher, Toilet and Ice Maker Unit Information:

* The FloodStop valve is connected to the angle stop and supply line

* Water/leak sensor is placed at the base of the appliance or fixture (Dishwasher; Sink; 3/8" Icemaker; Toilet; etc.)

* Valve stays open until water loss is detected

* Water on sensor closes FloodStop valve and sounds alarm * Valve stays closed until problem is attended to and system is reset

FloodStop 3/8 Inch Water Valve and Water Alarm Components:

1. Motorized Full-Port Ball Valve (3/8" Compression).

2. Control Unit with Battery Backup (4 C batteries, not included).

3. AC Power Adaptor (or use 4 X C Batteries as Primary Power Source).

4. Water Leak Sensor.

5. Output Contact Wires (2).

Thank you for your question.

Sincerely,

Barbara