Safe-Home.com

Question about the Kids Edge Hearth Pad Metal Frame BROWN, to 78 in.

Answer: This is the correct hearth pad for an irregular stone hearth. First, the hearth must be at least 1.5 inches above the floor. Second, you will need to purchase an Kids Edge Metal Hearth Pad Extension, BROWN, 24 In. to add to the middle of your hearth pad for the proper length.

To install the hearth pad after unpacking:

1. Remove tape on tightening rod (6). Remove filler pad (2) from inside cardboard insert and set aside for later use.
2. There are two sections. The left side is completely covered with pad. The right side, partially covered with pad, slides under the left side for adjustment. You would add the extension to this part.
3. Then extend sections of unit and place on hearth.
4. Pull section together until snug on hearth.
5. Without allowing sections to slide, remove unit and turn over to expose tightening rod.
6. Insert rod hook into nearest hole and pull sections apart so there is enough tension to keep the hook in hole.
7. Reposition unit on hearth. Insert Phillips screwdriver into hole at right corner
8. Turn tightening bolt clockwise until tension is felt.
9. Make sure the unit is in place by pushing down and back at corners.
10. Tighten bolt further until unit is secure on hearth.
11. NOTE: if unit is not secure and tightening bolt will not turn further, then loosen bolt, remove unit and move adjustment hook to next hole. Now reinstall unit.
12. CAUTION: IT IS POSSIBLE TO TIGHTEN BOLT TOO MUCH CAUSING ENDS TO FLARE OUT CAUSING LOSS OF GRIP.

CUTTING FILLER PAD

1. For appearance, this step is IMPORTANT. Measure the gap where frame is exposed. Add 3/8 inch to that measurement and mark the filler pad
2. Place pad on edge of cardboard box, matching mark on pad with black alignment on box.
3. Use only a sharp long-blade knife such as a fillet knife. DO NOT use a razor knife, utility knife, or other short-blade knife.
4. Lubricate entire length of knife blade with liquid soap or soapy water.
5. With light pressure, move knife back and forth, keeping the blade straight with alignment line.
6.  After top half of pad is cut, turn pad over and repeat.

IMPORTANT NOTICE: The Cardinal Gates Metal-Backed Hearth Guard is designed to help prevent injuries. However, it is always possible for some injuries to occur even thought a protective device is used. We suggest adult supervision at all times. PAD IS “UL RECOGNIZED.”

INSTALLING FILLER PAD

1. Peel off adhesive backing that bonds to front of frame only.
2. Carefully press right end of filler pad against pad on right side of frame.
3. Allow filler pad to rest on top of frame while pressing front of pad into place.
4. Once the front of filler pad is bonded to frame, lift top corner of filler pad and peel off remainder of adhesive backing.
5. Now press down on top of filler pad to bond to frame.
6. Installation is now complete. To remove unit, simply loosen bolt to release tension.

Thank you for your question. Enjoy your little one: she will grow up way too fast!

Sincerely,

Barbara

Question about metal safety gates for outdoor use.

Answer: Safe Home sells several metal gates that will fulfill your needs. All Cardinal brand gates are JPMA certified & adhere to guidelines as set forth by the JPMA & the Consumer Products Safety Commission.

Cardinal Stairway Special Gates come in brown , black and white gates with stainless steel hardware. The Stairway Special Outdoor Gate (Model SS-30OD) come with stainless steel hardware. Optional stainless steel mounting kits are available for Stairway Special Gates bought without the stainless steel hardware.  These safety gates are powder coated so the finish is long-lasting and easily cleaned. Features include a latch system that baffles toddlers yet allows one hand operation for adults, and an optional stop bracket prevents opening over a stairway for greater safety. The Stairway Special will mount at angles up to 30 degrees allowing location of a stud when mounting on drywall.

Stairway Special Gate Features:

• Gate width is adjustable 27 inches  to 42. 5 inches
• Height: 29.5 inches
• Bar Spacing: 2.5 inches
• Width extensions: 10.5 inch extension (Model BX1) extends width from 42.25 inches to 53 inches. 21.75 inch extension (Model BX2) increases width from 42.5 to 64 inches.

Cardinal Gates Duragates are available in white and taupe. This steel gate is powdercoated for durability. Model MG-25 has a simple mounting system, easy assembly and can mount at any angle. If you need a taller gate, the Duragates also come with height extensions. There are two models, the taupe gate and the white gate, each with an 8 inch height extension included. A total of two extensions can be added increasing the height a total of 16 inches.Width extensions are also available in in white or in taupe.

• Width is adjustable from 26 ½" to 41 ½"
• Height 29 ½"
• Bar Spacing 2 ½"
• 12” extension (Model BX12) is available for openings 41 ½" to 54"

Please measure carefully. Gates are returnable only if damaged in transit or in unopened boxes. Hope this helps.

Thanks for your question.

Sincerely, Barbara

Question about the Window Wedge Adjustable Velcro Window Stop,144/CS window stop product for slider windows in military housing.

Answer: The Window Wedge fits on the window frame, not in the tracks. Make certain that the window frames are wide enough as Window Wedge® uses one 8 inch velcro strip to which you velcro the 4 inch wedge portion. This product is made in the USA. We asked you to have your customer measure the windows and they are 3/4 inch wide. We recommend that you have two wedges i.e. one package installed on each window. That is because a child pulling on a slider could possibly pull the unit out of the track.

Each window wedge loop strip is 8 inches long and 3/4 inches wide.The actual wedge section is 3.25 inches long.To open the window greater than four inches for cleaning, remove the wedge from the velcro loop portion of the window stopper.

To Install Window Wedge Window Stoppers On a Slider Window:

    Close window. Clean window frame surface before application of loop strip.
    Peel off backing of 8 inch loop strip and place in center of upper horizontal window frame (not on the glass)
    Attach the Window Wedge® to the loop strip with the
    two tines facing the adjacent window section.
    Slide window open until contact is made with the Window Wedge®
    Attach the second Window Wedge® unit to the bottom part of the
    Adjust the position of the Window Wedge® so that the
    window opening is 4 inches or less.
    Note: For maximum child safety, maximum window opening should not exceed 4 inches.

To Install Window Wedge Window Stoppers On a Double Hung or Single Hung Window:

    Close the window
    Clean the surface of the window trim prior to application. Do not attach to glass itself.
    Peel off the backing from the 8 inch loop strip and place in the center of the upper window frame for a double hung or single hung window.
    Attach the Window Wedge® to the loop strip.
    Attach the second window wedge on the other side at the same height.
    Open the window until it is stopped by the window wedge.
    Note: For maximum child safety, maximum window opening should not exceed 4 inches.

Safe Home does offer bulk pricing on this product. Please contact us directly if you need over 144 packages.

Thanks for your question and your purchase!

Sincerely, Barbara

Question about using Grip On® with a epoxy coated concrete floor or polyaspartic flooring coating.

Answer: I contacted the manufacturer for clarification on this interesting question. The answer is no. For an anti-slip floor, Grip On will not work after epoxy or polyaspartic coatings are applied to concret: the coatings fill the pores. What Grip On anti-slip floor solution does is fill in the pores invisibly to increase the resistance to slipping and falling. So Grip On® would not work in your situation. Also if you paint a concrete floor, the same situation occurs as the paint fills the pores.

One solution to your problem is to add a color dye to the concrete and use a water based xylene sealer: you want nothing to seal the pores of the floor as then it cannot be treated with Grip On®. 

Why does Grip On work? All natural materials such as concrete, ceramic, marble, granite, terrazzo, quarry tile, slate, porcelain tile and bathtubs have natural voids in them. The larger the void, the more the surface of that material is slip resistant. This void creates a tread for you to walk on.  Ceramic or glazed tile, as well as porcelain, are coated to create a shiny finished look to a floor or fixture. These coatings fill in the natural voids up to 70%. When you walk on the dry surface, you would not notice that the voids are filled. But, when the surface is wet, the water fills in the remaining 30% of the void and that is why a floor becomes slippery not allowing any space between the water and the bottom of your foot creating a hydroplane effect. Grip On® microscopically treats the surface of your floor or fixture in a way that brings back the natural void via the treads in the surface material. So, when a floor or bathtub is wet, it still allows you to feel surefooted. Grip On® Anti Slip Solution is a clear, chemical treatment that increases the co-efficient of friction and the safety of the surface when wet.

We sell Grip On® in various sizes from 4 oz bottles to drums. Among the sizes are

• Grip On® Anti-Slip Solution for Floors, 4 Oz. Bottle for up to 12 square feet of treated surfaces such as porcelain bathtubs, ceramic tile showers, etc.
• Grip On® 16 ounce bottle to treat up to 48 square feet.
• Grip On® One Gallon Size to treat up to 400 square feet of surface,
• Grip On® Anti-Slip Hard Surface Floor Solution, 5 Gallon to treat up to 2000 square feet of hard surfaces
• Grip On® Anti-Slip for Hard Floors and Tubs, 55 Gallon to treats up to 22,000 square feet of flooring.

We also sell Grip On in a pallet of four 55 gallon barrels. With the drums, the lid stays on. What you do is purchase a vacuum or hose pump from your local hardware store. The lid has one 4 inch hole and one 2 inch hole so you can pump the Grip On out into containers you use for your applicators for spreading.

1. Clean and rinse area.
2. Pour Grip On™ on surface.
3. Mop or sponge area liberally.
4. Let stand for 15 to 20 minutes.
5. Rinse off with clean water.
6. Area is now ready to use.

After treatment, do not wax. Wax fills in the enhanced read created by the Grip On™ treatment. Reapply every 2 years for bath and shower areas. Reapply every year for traffic areas.

Additional Questions and Answers about Grip On®:

Q: How does Grip On® Anti-Slip Solution work?
A: Grip On® Anti-Slip Solution is a process that increases the coefficient of friction on a tile floor or a porcelain bathtub. This is not a coating that can wear off: this is a process that creates a tread design on the mineral surface itself.

Q: Does the treated surface look or feel any different?
A: There is no discernible change in appearance. However, when wet, the feeling is SAFE!

Q: Why is there a need for Grip On® Anti-Slip Solution?
A: Slip/Fall accidents are the nation's #2 accidental killer. Over 9 million disabling injuries every year. Business insurance rates are skyrocketing. Increases of 25% annually are common.

Q: How long is the Grip On® guarantee?
A: 2 years for bathtubs and showers. 1 year for traffic areas.

Q: Is Grip On® Anti-Slip Solution difficult to apply?
A: No, Grip On® is easy to apply. One worker can treat hard surfaces at the rate of 600 square feet per hour, per worker. Bathtubs require less than 10 minutes with no strenuous work.

Q: Does Grip On® Anti-Slip Solution kill germs?
A: The chemical in Grip On® Anti-Slip Solution is known to inhibit bacterial and fungi growth and to kill some bacteria and fungi. Test data is being gathered on germ killing and will be available at a later date.

Q: If my floor is sealed, can I still use Grip On® Anti-Slip Solution?
A: Yes, Grip On® Anti-Slip Solution works through most floor seals and effectively applies the “invisible tread.” Two applications may be required for sealed floors.

Q: What if there is grease on my floor?
A: Grip On® Anti-Slip Solution loosens grease, making it easier to remove any grease on your floor. More than one application may be required. Once again, it may take more than one application. Grip On® Anti-Slip Solution will loosen all hardened grease on your floor.

Q: Can I wax over the Grip On® Anti-Slip Solution?
A: NO. Wax fills in the “invisible tread” that Grip On® Anti-Slip Solution placed on your floor. We recommend a dry buff to bring up the shine.

Q: Is Grip On® Anti-Slip Solution dangerous?
A: The level of danger is similar to household bleach. Similar cautions are on each bottle. Keep out of reach of children. Avoid eye contact. Wear rubber gloves. Use in ventilated area. Can be fatal if swallowed. Do not use on wood, vinyls or plastics

Grip On Anti-Slip Solution Specifications:

• Use on tile floors, bathtubs, showers and on almost all hard surfaces, such as ceramic tile, glazed brick, marble, polished stone, terrazzo, river rock, concrete, and quarry tile.
• Coverage:
  • 4 oz. bottle: 12 sq. ft.
  • 16 oz. bottle: 48 sq. ft.
  • Gallon: 400 sq. ft,
  • 5 Gallon Bucket: 2,000 sq. ft.
• Increases the anti-slip CEF by 100% to 500%.
• Chemical Name: Hydroxy Acetic Acid.
• Physical State: Clear yellow, mild odor.
• pH: 7.6.
• Caution: Keep out of reach of children. Avoid eye contact. Wear rubber gloves. Use in ventilated area. Can be fatal if swallowed. Do not use on wood, vinyls or plastics.
• Warranty: 1 year limited manufacturer's warranty on traffic areas; 2 years on bathtubs and showers. If the customer installed Grip On^® Anti-Slip Solution, the company will send additional material to the customer at no cost excluding shipping
• Disclaimer: GRIP ON^® ANTI-SLIP SOLUTION helps to reduce the risk of slip/fall accidents, but Safety Seal Products Corp its' agents and representatives do not warrant or guarantee to the customer, or any other person or party, against the Occurrence of slip/falls, or other accidents, personal injury, or property damage of any nature. Accidents and falls may occur on treated areas, notwithstanding its treatment with Grip On^® ANTI-SLIP SOLUTION and customer AGREES to indemnify and hold harmless Advanced Floor Care Products and its agents and representatives, free and harmless from any damages, claims, demands or causes of action arising in connection with or brought by anyone allegedly slipping, falling, tripping, or stumbling on treated area.

Question about options to window guards.

Answer: Safe Home sells three different types of window stops. The Window Guardian Super Stopper, The Window Wedge and the Window Guardian Lock. The best choices still are window guards. The John Sterling Window Guards can be locked with a removable lock and swing open for cleaning windows. These are not expensive but would require a handy man type person if you cannot do the installation itself. The Guardian Angel window guards are much easier to install. They are not lockable but do remove completely from the window mounts.

Window Guardian Super Stopper The fastest and easiest to install is the Window Guardian or Super Stopper window stop. This home safety device combines a 2.75 inch flexible suction cup with a unique shaped wedge (1.25 inch x 2 inch). Clean the window. Open the window 4 inches or less. Suction cup on the stops on either side of the single hung window lock mechanism or along the sides of the sliders (as high as you can). These are also great to limit sliding door openings if you have children you want to keep inside the house.

Window Wedge: The next easiest to install is the Window Wedge®. The Window Wedge® uses two 8 inch velcro strips that are 3/4 inches wide. The wedge portion is removable so you can open the window opening wider for cleaning. The that fit on the window frame itself. Made in USA.

To Install Window Wedge Window Stoppers On a Double Hung or Single Hung Window:

    Close the window
    Clean the surface of the window trim prior to application. Do not attach to glass itself.
    Peel off the backing from the 8 inch loop strip and place in the center of the upper window frame for a double hung or single hung window.
    Attach the Window Wedge® to the loop strip.
    Attach the second window wedge on the other side at the same height.
    Open the window until it is stopped by the window wedge.
    Note: For maximum child safety, maximum window opening should not exceed 4 inches.

To Install Window Wedge Window Stoppers On a Slider Window:

    Close window. Clean window frame surface before application of loop strip.
    Peel off backing of 8 inch loop strip and place in center of upper horizontal window frame (not on the glass)
    Attach the Window Wedge® to the loop strip with the
    two tines facing the adjacent window section.
    Slide window open until contact is made with the Window Wedge®
    Attach the second Window Wedge® unit to the bottom part of the
    Adjust the position of the Window Wedge® so that the
    window opening is 4 inches or less.
    Note: For maximum child safety, maximum window opening should not exceed 4 inches.

Window Guardian Window Lock. The push-button key lock design is a patented feature. Remove the key to keep the window locked. Easy to use, this security lock provides peace of mind and installs easily in minutes. The Window Guardian has a tamper-resistant cover and fits most windows. Requires a screwdriver for installation. White.

Before installation, remove the pull-key and cover.

1. Push the button while pulling the pull-key until it comes free. To remove cover, push down and slide it along the base towards the pull-key end.

2. Place the base on the spacer and line up the screw holes. Using the three #6 at head wood screws attach the base to the window or sill so that the end of the base is close to the edge of the sill or window.

3. Place the pin body onto the base so that the location tab ts into one of the three position slots. Select the position slot that gives the closest t to the keeper without causing interference.

4. Slide the cover along the base from the pull key end until it snaps into place. If it seems to bind, turn the cover around to position the locking bump at the correct end.

5. Place the pull key into the back of the assembled body and rotate gently until it finds the correct alignment and push the button, locking it in place.

6. Locate the keeper and install with the two #6 pan head screws. Clip the cover over the keeper to hide the screws. (Fig 3) An alternate orientation of keeper for vertical mounting is supplied. Use the second keeper as a holder for the pull-key when not engaged in the lock.

7.For aluminum windows, fit the lock to the aluminum adapter with 3 #6 machine screws. Fit the aluminum adapter to the handle or the flange at the end of the window. Secure the adapter with 2 Allen screws with Allen key provided. Use the appropriate keeper or drill a hole in the sill when required.

How to Use the Window Guardian: To unlock, pull the Pull-key and rotate 90 degrees/ the key button does not have to be pressed. The Pull-key can be left in. To remove the Pull-key, press the Pull-key button and pull until the key pops out. A second keeper is supplied as a location to store the Pull-key when not engaged in the lock. To insert the Pull-key into the key hole, rotate the key gently until it slides into alignment with the key hole. Once aligned, press the key button and push the key further into the key hole until you hear a click. Additional holes or keepers can be used to create locking positions that allow for partially open windows. Made in China.

Note: None of these products are substitutes for adult supervision. Never leave a child unattended with an open window. Thanks for your question.

Sincerely, Barbara

Question about how you wash your window glass when you have Guardian Angel Window Guards installed

Answer: Guardian Angel window guards are easy to install and easy to remove, for an adult or older child that is. These window guards are now standardized in the side mount heights as well. That means if you move and choose to remove the window guards to use in your new home, you can drill out the screws and re-install them. Unlike the John Sterling window guards, the Guardian Angel remove completely from the mounting bars.

For your single hung windows, mount a window guard or two or three for taller windows by mounting the lowest mount bar two inches above the sill. Then stack additional mounting bars as needed by butting the ends of the mounting bars together. Then telescope the window bars to lock into the mounting bars.Some people prefer to mount the window guards to cover the entire window. In this case use the longer, taller bars and mount vertically.

If you mount in sliders, the best way is like prison bars. Once more you decide the width opening you want and mount units side by side to fill that space. Yes, prison bars may not be attractive but they don't give your child a ladder to climb!

Each window guard has four locks, two on each side of two of the window bars. For example, there is  one lock on one side of bar 1 in a 3 bar unit and another lock on the other side. Bar 3 has an additional pair. You push in two locks at one time to release the bar. Push to the other side and release the second side. To reinstall, do the reverse. Make sure the bars lock into the side or top and bottom mounts.

Guardian Angel window guards are strong, powder coated white steel. They come in sizes that expand from 14 to 17 inches to those that expand from 73 to 120 inches. There are 3, 4 and 5 bar units that you can mix or match to meet your window protection needs.

Use a pair of Window Wedge window stops or a pair of Window Guardian Super Window Stops to keep the windows from opening more than 4 inches beyond the bars.

Thank you for your questions. Go to any window guard web page for access to our window guard guide.

Sincerely,

Barbara

Question about the Fridge Guard Appliance Child Lock, CLEAR, the Fridge Guard Appliance Child Lock, WHITE and the Double Door Fridge Guard, Child Safety Strap, Black

Answer: We sell three products. The first two are identical except one is clear and the other is white. These are the Fridge Guard appliance locks to keep kids out of refrigerators. The only other option to consider is a chain with combination lock that wraps around the entire unit. For the chest type freezer, I have no suggestions.

Here is the Fridge Guard information. This works on single door units. Parent Units' Fridge Guard Appliance Child Lock is a clear or white plastic refrigerator safety latch closure that uses high-bonding adhesive that will not mar refrigerator surface. This removable refrigerator lock or freezer door lock uses latch and hook to secure doors from young children. This child safety product is made in the USA. This sturdy child safety lock also protects against dumps, spills, or doors left ajar.
 
    * Easily Installed: Apply latch to side or top for double doors and freezers. Remove red liner from hook. Apply to door with hook facing forward. Install latch in desired location. Press firmly for 20 seconds. Allow adhesive to set overnight.
    * Easily Used: To open refrigerator, press inward on door handle and release flexible latch over hook. Latch resets automatically when door closes.
    * Easily Removed: Gently pry off hook and latch. Use olive oil to remove any adhesive residue.
    * Clear or White.
    * Note: Use as freezer door lock or refrigerator lock to keep younger children safter. For unused refrigerators or freezers, install latches to extend one inch beyond the hooks. Insert up to a 1-inch block of foam or plastic for ventilation through door opening. Refrigerators or freezers with ventilation are less likely to have mold or mildew problems.
    * Remember: No protective device takes the place of adult supervision.

Parent Units' Double Door Fridge Guard  is a black buckle style lock for double door refrigerators or on the refrigerator doors of trio style refrigerators. This child safety device is easily installed and easily removed by adults. If you have an unused double door refrigerator or one in the garage or basement where you store alcoholic beverages, use this safety device to make sure children stay out. The durable rubber strip combines with a patented buckle to securely lock fridge doors.  This stops your children safer from dangerous items or from leaving doors open causing food disasters.

Parent Units' Double Door Fridge Guard :

    * Simple to install
    * Easy buckle lock/unlock for adults to use
    * Keeps double door fridges off limits to little ones.
    * For use on standard kitchen and bathroom cabinets.
    * All childproofing works better when children are not present. We advise you install home and child safety devices when children are asleep for the night.
    *Warning: Always rely on supervision as your best defense against accidents and injuries. Prevention is paramount. True this product is a highly reliable backup, but no product can be 100% fail safe. Proper Installation required. Use a licensed contractor for best performance.

Below are the product performancy warranties for both units:
Product Performance Warranty: This product must be used with supervision. Due to uncertainty of forces generated and numerous variables involved in a jarring event, no warranty can be properly applied to the performance of the product. Parent Units' only responsibility shall be to replace any product proven to be defective in material and workmanship prior to installation of the product. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising out of the use or misuse, or the inability to use the product installation, whether by the user or third party, constitutes acceptance of these conditions by the user.  

Thank you for your question. I only remember once that one of my sons opened the freezer door and actually turned off the freezer. I did a lot of cooking the next day and threw out a lot of once frozen products.

Sincerely,

Barbara

Question about the Door Guardian door lock for use on basement doors and pantry doors.

Answer: Yes, the Door Guardian is a terrific child safety device to keep inward swinging doors closed to curious children. When my sons were young, we had a similar set-up and had to install a double turn dead bolt lock high on a hollow core door, a rather permanent installation.

Installation sometimes means mortising out the door frame as the unit has to be level when installed. The lock portion should not cause any harm to the door itself. Mount the Door Guardian high on the door frame so that only older children and adults can reach it. Otherwise, you could find yourself locked in the basement! This is a great addition to a pantry door and a lot less expensive that the combination door lock my son and his wife installed to keep the children from midnight raids that left the kitchen a mess.

Mount the Door Guardian unit at least six inches higher than the door knob or the deadbolt. Depending upon the door frame, you may have to mortise out an area so that the stationary part of the unit can be mounted straight, otherwise the lock part may not keep the door closed. Included are two long dry wall screws and three metal self-tapping screws if your door frame is metal.

Slide forward and flip closed to lock. Slide and turn to open the lock. This is installed on the side of the door with the door knob, on the side that swings inward.

Choose from:

• Silver Nickel Metal Finish Door Guardian Lock
• White Metal Finish Door Guardian lock
• Satin Chrome Finish Door Guardian Lock
• Antique Brass Door Guardian Lock
• Bright Brass Door Guardian Lock

Thank you for your question. Let us know if you have other child proofing concerns: we are happy to help you.

Sincerely,

Barbara

Question about the Boing Skin Urethane Foam Padding in Boing Fire Retardant Safety Wall Pad, 31x11.75 In, YELLOW, 4/BX, Boing Pole Pad or Post Pad 5 Inch Diameter - Yellow, Boing Edge Corner Strips-YELLOW, Case of 10 and Boing 3D Jumbo Corner Covers, YELLOW,4/PK.

Q; "I need to safety proof a warehouse. I've looked at various products. I'd like to know the advantages of using a skin urethane foam product rather than standard extruded foam which seems less expensive. Thanks. Thomas."

The main advantages are that this is a sturdy material and quite shock-absorbing and comes in products to meet almost every safety proofing need. Read on for more detail.

The Boing skin urethane products are safe for both commercial and residential uses, having passed or surpassed safety requirements including compression, toxicity, etc. Skin urethane has anti-bacterial properties and passes the ASTM G21 testing. There is no PVC, lead or phthalates in these products.  Although fire retardant, the Boing foam does not meet the current Class A fire codes for fire and smoke retardants. There are many different local, national and international fire codes, each with different property requirements so one product cannot meet all the possible codes.

Skin Urethane is long-lasting. Of course, there are instances where excessive use or aggressive use will reduce longevity. this was desifned as shock-absorbing safety padding to reduce injuries.
Size tolerance of skin urethane is within 5% in the size and density of the finished products. That is because skin urethane is molded, one piece at a time, and can be effected by temperature, humidity, season, weather, etc. Baking lasts about 30 to 40 minutes.

Boing safety pad products are usable indoors or outdoors. All safety padding products are UV treated but over time, like all plastics, there will be some fading. The stronger the sun, the faster the fading occurs. Darker colors fade faster. The impact absorbing qualities are reduced in very cold (below 32 F) and in very hot (over 100F) temperatures. The most UV resistant colors are the primary ones, red, blue, green and yellow. It is best if the product is not exposed to direct sunlight for extended periods.

Installation: We recommend GE-Silcone I, Silicone II or Silicone II (2X). Also 3M VHD (very high bond) tape is a great option
Aluminum re-inforced strips can be attached with screws (strips are pre-drilled & we provide the screws)

Amount of silicone needed: Varies withe the type of surface to be protected and the degree of adhesion. As a rough estimate, you can generally attach the following numbers with a single 300ml tube:

• Wall Pad - 2 to 3 wall pads per tube

• Edge Corner Strip - 6 to 8 edge corner pads per tube

• Jumbo Corner Guard - 12 to 14 corners per tube

• Post Pad - 1 to 2 post pads per tube. Remember this product fits only 5 inch diameter poles.

Cleaning and maintenance of safety padding: Use non-abrasive cleaners, normal household cleaning solutions. Permanent markers rarely can be removed.Use around water activities is fine. Do not cut or puncturer. Fasten to clean and dry surface. Chlorinated water will cause discoloration as will that with a high TDS rating.

Thanks for your question. Our most popular products for safety proofing are the yellow ones for obvious visual reasons!

Sincerely, Barbara

Question about installation of Boing Fire Retardant Safety Wall Pad, 31x11.75 In, YELLOW, 4/BX and Boing Edge Corner Strip,UV Treated,YELLOW, 25/CS

Answer: There are several options available to install safety edge corner strips and wall pads. Most customers use the silicone adhesive because it is less trouble and more permanent. Both products are available at most hardware stores.

1. ADHESIVE TAPE OPTION: 3M VHB (Very High Bond) tape #5925. The only tape that will adhere to both the safety cushion products and to most other surfaces. Requires 72 hours for maximum adhesion, more expensive than silicone.
2. SILICONE ADHESIVE: heavy duty adhesion, ability to add a bead around the outer edge to seal off from dirt, liquids or tampering. Adheres to almost any surface including rough textures like brick

3M VHB (Very High Bond) Tape #5925 Properties

• A very conformable, double-sided, pressure-sensitive, closed-cell acrylic foam tape with a PE film liner. 25 mil thick.
• Color: Black
• Width: 1/2" or 1 "
• Thickness: .06" (25 mil)
• Incredible VHB strength guarantees a strong bond.
• Soft conformable foam molds to irregular and textured surfaces.
• Bonds powder painted metal, acrylics and polycarbonates with minimal priming or sanding.
• Temperature range is -40°F to 250°F.
• Dampens noise, shock and vibration.
• Resists moisture, UV and solvents. Indoor/outdoor.

Wall Pad and Corner Cushion Tape Instructions:

1. Clean surfaces with mineral spirits or similar product to help adhesion
2. Peel & Stick
3. Wait for it to bond properly - IMPORTANT - bonding strength develops over time
- 20 minutes = 50% of ultimate strength
- 60 minutes = 75% of ultimate strength
- 24 hours = 90% of ultimate strength
- 72 hours = 100% of ultimate strength

We look forward to helping you with your industrial safety project or home safety product.

Thanks for your question.

Sincerely, Barbara