Safe-Home.com

Healthier Living | Child Safety | Eco Friendly Tips

Stop Under Sink Water Leaks With Floodstop Water Valve Unit for Hot and Cold Water Lines

by Barbara 22. July 2012 07:01

Question about the FloodStop for Sinks Lead Free Water Valve FS3/8CD.

Question: "Our neighbor recently had extensive water damage from a leak under a bathroom sink. The sink is in a rarely used bathroom. The first hint of the water leak was the damp spot on the ceiling in the room below. What product do you suggest for protecting our guest room sink which is rarely used? Thanks. Sam."

Answer:  For a single location, install the FloodStop for Sinks Lead Free Water Valve FS3/8CD. The "CD" stands for compression fitting, i.e. no soldering is required. The Floodcheck water valves connect to the angle stops and supply lines. FloodStop water valves are full port ball valves that meet the California and Vermont lead free water valve standards for drinking water.  Add additional sensors for more coverage under the sink. Do remember that you will need an unswitched electrical outlet for power: electricity is used only when the sensor detects water.

When a hot or cold water leak is detected, Floodstop shuts off the water below the sink and sounds an 87 db alarm.

Installation:

    Connect the water valve to cold and hot water lines under the sink.
    Mount the control unit.
    Place sensor(s) on floor.
    Plug power supply into an unswitched outlet. Note: electricity is used only when the sensor detects water.

NOTE: DO NOT PLACE SENSOR DIRECTLY ON METAL PAN OR DAMP FLOOR. If no water is present and alarm sounds, place paper towel or cloth under sensor to "insulate" against floor dampness or metal of pan. When the paper or cloth gets wet, the sensor activates the shut-off and sounds the alarm.

How FloodStop (FS 3/8-CD) Works:

    FloodStop valves connect to the angle stops and supply lines.
    Water leak sensor is placed at the base of the fixture (sink, laundry tubs, bathtub, etc.).
    Valve remains open until a water leak or water loss is detected.
    Water on the sensor signals the Floodstop controller which closes the valve and alarms.
    Valve remains closed until system is reset, and sensor is dry.

FloodStop (FS 3/8-CD) Components:

    Motorized Ball Valves (Two Valves, 3/8 inch Compression Fitting).
    Control unit with battery backup (4 C batteries, not included).
    AC power adaptor (or use 4 C Batteries as primary power source).
    Water leak sensor (1.25" X 7.5").
    Output contact wires (2).

Technical Specifications:

    UL Listed Class 2 Wall Adaptor, 115AC/9VDC.
    UPC listed, full port, motorized ball valves.
    Motor operates at 6VDC.
    Rated 0-180 PSI. Max 250 PSI. Solid brass.
    Signal outputs: 2 normally closed.
    Alarm: beeping with mute button.

Features:

    For added water detection protection, add more sensors. Sensors plug into sensors, NOT the Control Box.
    The 3/8 inch valve is 3.75 inches long.
    Controller has reset and test buttons to test valve performance plus battery back up.
    Easy to install, operate, and maintain.
    Designed for residential, condo and apartment dwellings.
    Full port ball valves automatically shut off water supply to sink when water sensor/sensors get wet.
    Power: 120VAC and/or battery backup (4 C batteries).
    No wires to route throughout the home.
    Alarm: beeping with mute button.
    Water Sensor: 1.5" X 7.5", double sided. Additional sensors may be added in series.
    AC Adapter Cord Length: 6 Ft.
    Wire Length from the Controller to the Valve: About 30 Inches Long.
    FloodStop Controller:
        3 buttons: Mute, Close Valve and Open Valve.
        Water sensitivity adjustment. Clockwise: less sensitive. Counter clockwise: More sensitive.
        4-pin connection to valve/sensor connector.
        Outputs: Normally closed. Contacts for any device that can utilize them, like auto phone dialers, alarm systems, X10 home automations devices.
    One year limited manufacturer warranty.

I hope this helps with your situation.

If you want whole house protection, a install the Floodstop Whole House Auto Water Valve System. This unit comes in 3/4”, 1” and 1.25” valve sizes. Included with each system are one Motorized Full-Port Ball Valve,one Controller (that shuts off the main water valve),four Sensor Modules, four sensors to place in areas you want protected, one transformer for the controller and four low voltage transformers for the sensor modules. This unit screws onto the water pipe, i.e. it is an NPT or National Pipe Thread Tapered Thread.

Go to WWW.SafeHomeProducts.com for more information.

Thank you again.

Sincerely,

Barbara